A 'more objective' take for Rational Audiophiles. Among other topics! X/Twitter:@Archimago E-Mail:archimagosmusings(at)outlook.com
[Some items linked to affiliate accounts - I may receive gift certs from qualifying purchases.]
Saturday, 21 November 2026
AlsoZone GaN Mono Amp - GaN tech, review, and measurements.
I suspect many of us in the audiophile community have heard of gallium nitride or GaN for short. Without going into the physics of it all (read up on it here, and also here), suffice it to say that GaN transistors, mostly consisting of a thin layer of AlGaN grown on GaN (pseudo-)substrate are the next big thing in solid state high-frequency technology. You'll hear terms like GaN FET or specifically HEMT (High-Electron-Mobility Transistors) internal architecture referring to this class of transistor. Specifically for Class D amps, they benefit from faster switching than MOSFET which is the fastest mainstream silicon technology today.
How fast is GaN, you might ask? Well somewhere like 3-10x faster.
In practice, if we look at the switching speed of silicon Class D amplifiers, they typically run somewhere around 300-600kHz whereas GaN designs can run around 1-2MHz at similar if not better efficiency. Tangibly, it is this better efficiency which results in less energy used, less heat produced, less cooling needs, and smaller size that we can look forward to.
Here are a couple of illustrations showing some theoretical gains that GaN can make:
Illustrative Efficiency vs. Power graph, typical amplifier classes.
Faster and more predictable GaN switching allows shrinkage of "dead time" compared to silicon (in nanoseconds). This reduces a crossover-like, odd-order, higher harmonic distortion. Feedback error correction can also be reduced.
That's theoretically all well and good! But as audiophiles, we'll no doubt be asking - What about sound quality? As usual, there will be good GaN-based amps and poor ones, it's a more difficult question to answer and will demand our own efforts, listening tests, informed by personal preferences. My perspective is that we can answer questions of high-fidelity through measurements at least - which might be most of what one needs, depending on philosophical leaning.
I obtained the device through the usual consumer channels; this review is not sponsored.
At the heart of this device are two important components mentioned in the product info:
TI PCM1808 ADC - 24/96 analog-to-digital converter with typical THD+N of -93dB fed by the analog input (RCA and balanced) sending out the I2S data to the...
Shenzhen Yongfukang Tech Co., Ltd. (ACME) ACM8816 - introduced in summer 2025, described as China's first domestic mono GaN HEMT chip amp with up to 300W power output. Said to be up to 97% peak energy efficient.
Already, that TI ADC's spec of -93dB THD+N gives us an idea of the upper limit of distortion plus noise performance which is still very reasonable if the rest of the amp performs well.
Here's a look at the box and contents:
Silver colored model also available.
We've got a few sheets of instruction, a couple of banana plugs if you have bare wires, and the amplifier itself. Other than the brand name and model, there's just the single whitish LED on the front (5-level brightness adjustable).
This amplifier is tiny, measuring 4.5" x 3.5" x 1.4" and weighs a mere 335g (0.74lbs).
Here's a look at the rear "business end" of the amp. You can see why they included the banana plugs if needed; the amp does not feature the typical binding posts for bare wires or spades. Rather, they're inset receptacles for banana plugs only.
Notice there's a 12V trigger which is great for mono amps as well as AUTO setting when a signal is present. There's a small FUNC button that can be used to turn on/off and change LED brightness.
There's the RCA-XLR switch for which input you're going to use (input impedance 10kΩ RCA, 20kΩ XLR/TRS).
The LOW-HIGH switch allows you to change the amp gain level (+27/+33dB RCA, +21/+27dB balanced). In principle if you don't need higher gain, keep it LOW for best performance (lower noise). With a 48V power supply, the company rates input sensitivity as 1.8Vrms RCA / 3.6Vrms balanced for low gain, and 0.9Vrms RCA / 1.8Vrms balanced.
Here's the Quick Start Guide which really should be all you need to operate the box:
Good that they have multi-level front LED brightness setting. I see there's also ability to set Auto mode sensitivity between fast (250ms) and slow (1s) response times in the manual.
A look underneath the box and you can see the holes for ventilation on the bottom and sides. Because of the energy efficiency of the amplifier, it's all passive (ie. no fans) and the chip might not even need an external heatsink. Throughout my testing, including pushing this amp above 100W into 4Ω for sometimes quite extended periods of time to the point where my power resistor gets quite warm, I could feel no neat from this little amplifier at all! This certainly feels different from other Class D amps I've tested.
Measured at the wall with the Kill-A-Watt meter, I see only 3W consumption with the amp turned on and idle.
The chassis construction is all one piece except for the bottom panel screwed to the top behind those warranty "Void if removed" foil stickers.
Here's the amplifier sitting beside a 38V/5A GaN switching power supply which I'll be using for the measurements. Note that this is the same power supply as what I used in the 3e Audio A5 Stereo review.
For reference, here's the rated power chart based on power supply:
So, extrapolating a little bit, for the 38V/5A power supply I have here, we're expecting something like 190W into 4Ω and around 100W into 8Ω with something like 1% THD(+N).
Okay, let's get to the heart of this device, how's the measured performance for something so inexpensive and small?
I. Objective:
Let's start with a digital oscilloscope reading of a 1kHz sine wave, 1Vrms to a 4Ω resistive load:
That looks really good. Clean sine wave, and notably there is no visible switching noise I can see at all unlike previous TI TPA chip amps (like the Fosi Audio V3 Mono). Great to see the noise getting filtered out. I didn't bother checking the switching frequency but I see from the ACM8816 datasheet that it can range as low as 384kHz and up to 2048kHz; I'm guessing that it's functioning at one of the higher rates like 1-1.5MHz.
Here's a look at a 1V, 1kHz square wave with output from my Topping D10s (24/96) with a steep linear phase filter firmware applied:
Interesting! Notice the square wave is showing minimum phase filtering. This means that the output from the DAC has been resampled at some point as it goes through the amplifier.
One of the important measurements we need to check is the output impedance:
Again, interesting. As you can see, it's very low below 1kHz but once we get to 4kHz, the output impedance has increased quite significantly to 0.5Ω. And by the time we hit 20kHz, it's out to about 2.5Ω!
This will have significant consequences on the frequency response. Unfortunate if you're running low-impedance loudspeakers:
As usual, I'm using my old Sony SS-H1600 speaker as an actual reactive load. The amp is not rated for 2Ω, clearly it has issues at high frequencies but nothing blew up with moderate levels up to 20W into 2Ω in my tests.
The frequency sweep above is supposed to be up to 48kHz (24/96 signal); notice that the output has been low-passed at 24kHz and using a minimum phase setting as suggested in the oscilloscope reading above. So whether it's at the ADC section or switching amp itself, the signal has being downsampled to a 48kHz samplerate.
Okay, so staying with the 4Ω load, how about typical 1kHz THD+N distortion measurements at various output levels?
As you can see, this amp is capable of about -70 to -75dB THD+N. Certainly not the lowest distortion or lowest noise device.
And how much power can it produce with that 38V/5A power supply into 4Ω?
About 180W by 0.1% THD+N (my usual threshold) into 4Ω.
And 95W by 0.1% THD+N into 8Ω. Both of these very much in line with what's expected using the 38V/5A power supply as per the power-supply chart above.
With the output level data, let's look at linearity:
As you can see, taking a direct output from the DAC I'm using, the amplifier clips by -5dBFS and linearity stays below 0.5dB deviation down to -105dB which means we have about a good 100dB range.
I was curious if using the balanced input improved the distortion profile in any way:
If we look at the red RCA and green XLR input curves into 4Ω load, notice that they're basically the same. There is no improvement in noise which is the primary limitation hampering the THD+N regardless of single-ended or balanced input. That -76dB THD+N level was also not surpassed with the 8Ω load.
Here's a THD (without noise) comparison to show that if it were not for the relatively high noise level, harmonic distortion itself is quite low and can dip into -90 to -95dB by around 1W.
Beyond the standard 1kHz single tone, let's have a look at the multi-tone test. Here's my standard Triple-Tone TD+N using 48/960/5472Hz tones at 2V and 4.5V into 4Ω:
As with the 1kHz THD+N, we're not looking at great performance with a reading of around -72dB TD+N.
Highest level of peak distortion within audible frequencies across the 32-reading average is down at -76dB which is about 12.5-bits noise/distortion-free range.
II. Subjective:
Since my intent in buying this was mainly for testing and maybe using it as a small mono amp on my testbench, I only listened to it one evening prior to putting it through the testbench as center channel amplifier to get a subjective impression. I used RCA input at low gain (+27dB) and my receiver's calibration menu to balance the relative level compared to the other speakers.
When I turned it on, I noticed only a very slight "tick" through the loudspeakers. Putting my ears close to the Paradigm Signature Reference C5, I can hear a slight hiss through the tweeter which is not obviously noticeable from the listening position at the low gain setting and more at high gain which should not be objectionable about 6+' away. This hiss is clearly more than through the Integra receiver.
I listened to a few multichannel albums with known stronger center-channel content to get a sense of how this sounds in relation to the Integra itself. A few albums I auditioned included SDE's TrueHD-Atmos remaster of George Michael's Faith (1987) which features George's vocals front-and-center in the middle channel on tracks like "Father Figure". It sounded pretty good although it must be said that the 1980's pop vocals have been processed with significant reverb. Nonetheless, the recording sounded well articulated, smooth, and not fatiguing. On tracks like "Monkey", the GaN Mono handled the dynamics well.
Let's get dancehall-reggae funky with Shaggy's "Angel" on Hot Shot (2000, multichannel EAC3-Atmos stream). Likewise, this sounded fine with the AlsoZone GaN Mono amp driving the center channel. With flat frequency response amplifiers, there's usually not much we need to do to get the sound integration reasonably close - so long as relative amplitudes are corrected and on multichannel systems, we can use DSP like Dirac and similar systems. (As discussed previously, amplifiers are not the most important components that affect sound quality, unlike loudspeakers and the room, so long as the amp is competent and of high fidelity of course!)
Since upmixing 2-channel audio will put a large amount of the content in the center, I had a listen to the stereo version of the Wildwood soundtrack (2026, also available multichannel) with Dolby Surround Upmixer. The first track "The Impassable Wilderness" has a nice, simple, fiddle solo that repeats across the 2.5 minutes along with some deep percussions. Again, I have no concerns with the dynamic impact through the GaN Mono compared to my usual experience. It's always hard to know for sure with sighted listening, but I did wonder if the placement and timbral details of that fiddle might have sounded a little less forward compared to the Integra driving that center channel.
So while I noted an increase in the background noise from this amplifier and maybe the detail retrieval might not be as precise, I think the amp was enjoyable driving the important center channel in a multichannel system even without further optimization like turning Dirac DSP on.
The 3e team engineered the AlsoZone GaN Mono. Here it the little GaN compared to their 3e Audio A5 and A7 Mono Class D offerings which are far from big amplifiers, yet they look like Goliaths compared to the little AlsoZone GaN Mono!
III. Summary:
Well, with this inexpensive AlsoZone GaN Mono, we have a taste of what GaN technology used in Class D amplifiers can do for us. The small size and cool-running nature of the amp will keep material costs down while potentially maintaining high fidelity. The very high switching speed will also allow better filtering out of the high-frequency carrier. And I certainly cannot complain about the amount of power this little box can put out!
However, from the perspective of a full-range hi-fi amplifier, I see this GaN Mono as currently a first generation product with refinement to be done. Just because a device uses GaN technology, this does not mean that it's going to have better sonic fidelity; a modern Class D silicon MOSFET module with good post-filter feedback will perform better than a GaN amp with less competent loop. While it sounds OK in my set-up as a mono center amp, the higher noise level may be evident in critical listening in a very quiet room (especially if you need high gain). We can easily see the limitations in the measurements.
For example, the output impedance is fine up to 1kHz, but the gradual increase beyond that will clearly be detrimental to loudspeakers with lower impedance in the upper-mid and "presence" regions. With this kind of pattern, I'd be more comfortable with the ACM8816 chip implemented in the GaN Mono as a cool-running Class D option for subwoofers; and suggest caution as full-bandwidth hi-fi amp (as you can see, many loudspeakers have low impedances >1kHz).
The other issue is the relatively high noise which is why we're stuck at best at THD+N of -76dB (SINAD 76dB). There's clearly a higher amount of hiss with this amp than most other amplifiers I've tried.
Finally, while IMO not as important in this era of "post-Hi-Res Audio", for the sake of being able to reproduce higher sampling rate content at least one octave above audible to something like 40kHz, it would be nice if future generations of these kinds of inexpensive GaN amps extended frequency response beyond the 24kHz limit we're seeing here. Since I've long considered 24/96 as beyond anything humans can hear, I think it'd be nice for an amp to give us the full 48kHz bandwidth.
Putting the pieces together, here's my AMOAR Score info-graphic for this AlsoZone GaN Mono amp with GaN 38V/5A power supply:
Important: this is with the 38V/5A power supply, buy the 48V/5A power supply if you need more wattage.
Having done measurements over the years on a few other Class D amps, we can compare this composite score with others. Here are some of the better but still very affordable Class D amps going back to the Hypex nCore NC252MP from 2020:
At this point, it's pretty clear that this little mono amp with its ACM8816 is not quite competitive with the current generation of inexpensive Class D MOSFET amplifiers based on chips like the TI PurePath TPA3522yet from the perspective of high-fidelity. There's still some work to do. But in time, with future generations of inexpensive GaN chip amps, I trust we'll see the rough patches improved, and achieve equivalent performance in smaller and even cooler running boxes like the AlsoZone GaN Mono.
In the meantime, the AlsoZone GaN Mono is a small, very affordable, cool-running package (great if you have limited room and need to place it where there's little airflow), that can still pack a lot of power and probably will perform more than good enough and be plenty enjoyable for most music playback situations around the home.
--------------------
To end, I mentioned the movie Wildwood (2026) above. What an amazing stop-motion animation flick - kudos to LAIKA Studios in Oregon! Good soundtrack as well if you're into movie music. As usual, the stereo mix has lower dynamic range than the multichannel version but they did a good job keeping dynamic range higher on this album (stereo DR10, multichannel DR12).
For the electronic-loving audiophiles, check out the newest Yello album Time Lab (2026, available on Atmos streaming) - here's "Break Out" which should give your system a workout:
As usual, I think this kind of music can really benefit from the extra spatial envelopment of multichannel sound.
Since this post is about an AlsoZone product, it's interesting to see that the brand has a number of multichannel amplifiers, typically based on the TI TPA3255 Class D device with PFFB and GaN power supply inside the box, available with excellent prices including 2-channel, 3-channel, 4-channel, and 6-channel variants.
As discussed last week regarding "new dimensions", when it comes to the hi-fi pursuit, as audiophile products progress with high-performance at lower price including for loudspeakers, DACs, subwoofers, and amplifiers, good multichannel systems can be built now at very reasonable cost. As usual, the main impediment to great sound I think is mostly the room we have for the hi-fi toys.
Happy Thanksgiving to the American friends with December and the holiday season arriving soon. How fast the the year passes!
Time to bring out the Advent music. Behold, probably my favorite version of "O Come, O Come, Emmanuel" (from Aaron Shust) in heavier style - pump it up: 😎
No comments:
Post a Comment